My Nighthawk Router Stopped Working. What should I Do?

Has your Nighthawk router stopped working? Well, it can be due to a number of reasons.

Sudden power outage
Wrongly performed Nighthawk router login for changing the router’s settings or incorrect settings have made on the router
Large number of files are downloaded on your router
Number of devices are connected to your router’s WiFi
Your router is overheated
Router isn’t configured properly
Firmware of your router is corrupted

No matter whatever the reason is behind “Nighthawk router stopped working suddenly” issue, this post make you familiar with one of the ultimate solutions to fix it including the Netgear router troubleshooting lights issue. Read on!

Power Cycle Your Nighthawk Router

The power cycling process will give your device some rest. Also, it will fix issues if the LEDs in your Nighthawk router are blinking continuously.

But, it is suggested that you power cycle your Nighthawk router in a proper manner. Else, you will loose access to your Nighthawk router.

Follow the instructions provided below in exact given order and know how to power cycle your Nighthawk router in a hassle-free manner:

Unplug the Nighthawk router’s power adapter from the wall socket.
Don’t forget to disconnect the currently connected devices from your main router.
Wait for some time.
Plug in your Nighthawk router back.
The LEDs on the router will become stable.

Now, you can connect your WiFi-enabled devices to your router’s WiFi and start using the internet without any hassle.

But, wait! For using the internet, you have to configure your Netgear Nighthawk router in a proper manner. Don’t know how to setup Netgear router? Worry not! Follow the instructions highlighted below and know the process of configuring the router. Continue reading!

How to Setup Nighthawk Router?

Power on your Nighthawk router. Let the LED on your router become lit and green.
Connect it to your existing modem using an Ethernet cable.
Turn on a PC or laptop.
Launch a web browser of your choice.
Input 192.168.1.1 or routerlogin.net in the browser’s address bar.
Press Enter.
Netgear router login page displays.
Enter the default routerlogin credentials into the provided fields.
Click Log In.
Netgear Genie setup wizard displays.
Follow the on-screen instructions.

Once your router gets configured successfully, you will be able to access the internet on all your connected devices without any hassle.

Stuck at any point while configuration? Ensure the following!

Make sure that your Netgear Nighthawk router is plugged in properly and getting continuous power supply.
The wall outlet you are using must not be fluctuated or damaged.
Your router and modem must be connected properly via Ethernet cable or using a wireless source.
Ensure that the web or the IP address isn’t entered in the browser’s search bar.
Make sure that the web browser you are using is up-to-date. Routerlogin.net web address or 192.168.1.250 IP do not work on an outdated web browser.
Be sure that you have the correct Nighthawk router login credentials. Refer to the Netgear router manual for the same.

Still your Netgear router not working after power cycling? Tried hard to fix the issue but nothing worked, not even the configuration? Fret not! The only option that you are left with is to reset Netgear router back to factory default values.

Here’s how to reset Nighthawk router:

Firstly, what you have to do – disconnect your modem with router.
Wait for a couple of minutes.
Locate the Nighthawk router reset hole.
As soon as you found it, press it very carefully and gently using a paper clip or pin.
Hold the router’s reset hole for a few seconds.
Release it.

Your Netgear Nighthawk router resets successfully. Now, you can reconfigure your Netgear router using the instructions listed above.

Also Read –Considering Options For The Best Gaming Mouse Bungee

Was the article helpful? Please share your feedback with us. And if you need more assistance to fix “Netgear router stopped working suddenly” issue, let us know via comments.